No products in the cart.
TQC Sheen coating inspection equipment and lab equipment for inspecting paint and coating applications and surface measurements.
TQC Sheen
Showing 1–48 of 63 results
- Adhesion, ASTM D3359, ASTM D4417, ASTM D4417-B, BS 7079-B4, IMO MSC.215(82), ISO 2409, ISO 2808-3, ISO 8501-1, ISO 8502-3, ISO 8502-4, ISO 8502-6, ISO 8502-9, ISO 8503-01, ISO 8503-02, Optical Inspection Tools, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics, Surface Cleanliness/Preperations, Surface Profile, US Navy NSI 009-32, US Navy PPI 63101-000
Pretreatment Test Kit (PTK) Basic or Full Kit – SP7315 or SP7316
Adhesion, ASTM D3359, ASTM D4417, ASTM D4417-B, BS 7079-B4, IMO MSC.215(82), ISO 2409, ISO 2808-3, ISO 8501-1, ISO 8502-3, ISO 8502-4, ISO 8502-6, ISO 8502-9, ISO 8503-01, ISO 8503-02, Optical Inspection Tools, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics, Surface Cleanliness/Preperations, Surface Profile, US Navy NSI 009-32, US Navy PPI 63101-000Pretreatment Test Kit (PTK) Basic or Full Kit – SP7315 or SP7316
The Pretreatment Test Kit is especially composed to control all relevant parameters during the pretreatment of steel prior to painting. The PTK is available as BASIC KIT and FULL KIT.
See Datasheet for Basic and Full kit comparisons
SKU: n/a - Adhesion
Cross Cut Adhesion Test Kit CC1000 (exclud. knife) VF1856
CC1000 BASIC (holder only) VF1848 includes the TQC Cross cut tester CC1000 Basic (Holder only, knives and accessories not included).
CC1000 KIT VF1856 includes a soft grip handle (Excl. knife, this needs to be ordered separately), nylon brush, illuminated magnifier, adhesive tape (adhesion to steel 4.3N/cm), a 4 mm Allen key, and a sturdy case
SKU: VF1856 - Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140
CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.
FULLY ADJUSTABLE
The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.
SKU: SP1695 - Adhesion, BS EN ISO8502-2, Surface Cleanliness/Preperations
TQC Dust Test Kit – SP3200
The TQC Dust Test Kit according to ISO 8502-3 allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish. The dust test kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust.
SKU: SP3200 - Adhesion, Scratch Testing
TQC Cross cut tester CC1000 Basic (Holder only, knife not included) – VF1848
Adhesion, Scratch TestingTQC Cross cut tester CC1000 Basic (Holder only, knife not included) – VF1848
TQC Cross cut tester CC1000 Basic Test Kit (Holder only, knife and accessories not included) – VF1848
Buy knives by adding them below or click here
View the CC1000 Kit with Holder and Accessories (exclud. knife) here.
SKU: VF1848 - ASTM D823, Automatic Film Applicator, Drying Time, Film Application
Compact Automatic Film Applicator – AB3652
ASTM D823, Automatic Film Applicator, Drying Time, Film ApplicationCompact Automatic Film Applicator – AB3652
The TQC Sheen Compact Automatic Film Applicator application speed can be set from 1 to 150 mm/s. The Compact model is suitable for both wire wound rod applicators and block applicators. Operating is easy through the standard TQC Sheen operating interface. The Automatic Film Applicator Compact Compact is available with a glass bed or a perforated vacuum bed sold separately.
SKU: AB3652 - Abrasion Testing, Hardness / Scratch Resistance, Hardness Tester, Scratch Testing
Comprehensive Abrasion Test TB5000 & TB5005
Abrasion Testing, Hardness / Scratch Resistance, Hardness Tester, Scratch TestingComprehensive Abrasion Test TB5000 & TB5005
The Comprehensive Abrasion Test is a universal test machine to test the coating abrasion resistance on beverage cans or flat materials. The reciprocating motion mimics in-the-field transportation abrasion damage of coatings equivalent to the Gavarti Associates “GV-CAT” system. The Comprehensive Abrasion Test is used in coating test laboratories for quality control work.
SKU: n/a - Abrasion Testing, ASTM D2486, ASTM D3450, ASTM D4213, ASTM D4828, ASTM F1319, Hardness / Scratch Resistance, Hardness Tester, ISO 11998, Scrub Abrasion | Washability Tester Supplies & Accessories, Wet Abrasion Scrub | Washability Test
Scrub Abrasion and Washability Tester AB6000 & AB6010
Abrasion Testing, ASTM D2486, ASTM D3450, ASTM D4213, ASTM D4828, ASTM F1319, Hardness / Scratch Resistance, Hardness Tester, ISO 11998, Scrub Abrasion | Washability Tester Supplies & Accessories, Wet Abrasion Scrub | Washability TestScrub Abrasion and Washability Tester AB6000 & AB6010
The Scrub Abrasion and Washability Tester tests the resistance of paint, varnish or coatings to scratching, wearing, and color loss due to wet or dry abrasion.
Please call (810)797-8300 for assistance with ordering all the components you need for your setup. You may browse options on the Ordering Page here
SKU: n/a - Accessory Products, ASTM D 2162, BS EN ISO / IEC 17025, ISO Guide 34, Viscosity, Viscosity Accessories
TQC Sheen Viscosity Calibration Oils
Accessory Products, ASTM D 2162, BS EN ISO / IEC 17025, ISO Guide 34, Viscosity, Viscosity AccessoriesTQC Sheen Viscosity Calibration Oils
Viscosity Calibration oils are manufactured in accordance with ASTM D 2162, the primary method for viscosity standards manufacture. They are fully traceable to national standards and are test equipment compatible. They are dual UKAS certified to the International Standards BS EN ISO / IEC 17025 and ISO Guide 34.
SKU: n/a - Hardness / Scratch Resistance, Hardness Tester
TQC SHEEN Automatic Scratch Tester – SP0100
The TQC Sheen Automatic Scratch Tester enables customers to test coating hardness on coated metal test panels with improved repeatability. Test for scuffing and measure scratch resistance quickly and easily with this handy automated scratch hardness tester.
SKU: SP0100 - ASTM D823, Automatic Film Applicator, Film Application
TQC SHEEN Small Automatic Panel Sprayer (1 gun) (4500N) – SH0586
ASTM D823, Automatic Film Applicator, Film ApplicationTQC SHEEN Small Automatic Panel Sprayer (1 gun) (4500N) – SH0586
TQC Sheen Small Automatic Panel Sprayer, 1 gun (previously 4500N) with configurable lift settings. It also has a switch with custom predefined Lift factory settings. The lift setting can be configured in steps of 10mm up to maximum of 500mm.
SKU: SH0586 - ASTM D823, Automatic Film Applicator, Film Application
TQC SHEEN Medium Automatic Panel Sprayer (2 guns) (4700N) – SH0590
ASTM D823, Automatic Film Applicator, Film ApplicationTQC SHEEN Medium Automatic Panel Sprayer (2 guns) (4700N) – SH0590
TQC Sheen Medium Automatic Panel Sprayer, 2 guns (previously 4700N). The models SH0582 and SH0581 are 2 new models, which are also based on Sheen models 4500N and 4700N, however with configurable lift settings.
SKU: SH0590 - Paint Thickness Gauge, Wet Film Thickness, WFT Wet Film Thickness
Paint Wet Film Thickness Combs (25-Pack) WF-SD
Paint Thickness Gauge, Wet Film Thickness, WFT Wet Film ThicknessPaint Wet Film Thickness Combs (25-Pack) WF-SD
Purchase a 25-Pack of Wet Film Thickness Comb Gauges come in a square card shape measure 1 – 80 Mil Scale or 25 – 2032 Micron Scale and are used in standard practices for measurement of wet film thickness of organic coatings by notched gauges. It is compact, low cost, and wallet sized.
Sold in packs of 25.
SKU: WF-SD - Elasticity Testing, Resistance & Deformation
TQC Sheen Set of 14 Mandrels for CYL Bend Test 100MM – SP1835
Elasticity Testing, Resistance & DeformationTQC Sheen Set of 14 Mandrels for CYL Bend Test 100MM – SP1835
TQC set of 14 Mandrels, width 100mm, for TQC Bend Test 100 mm.A set of 14 mandrels with a diameter of 2, 3, 4, 5, 6, 8, 10, 12, 13, 16, 19, 20, 25 and 32 mm. Includes Desktop holder (can also be wallmounted).
SKU: SP1835 - ASTM D 1894, Coefficient of Friction / Peel, ISO 8295, Surface Characteristics, TAPPI T 549
Coefficient of Friction / Peel Tester model 32-76e – – AB5700
ASTM D 1894, Coefficient of Friction / Peel, ISO 8295, Surface Characteristics, TAPPI T 549Coefficient of Friction / Peel Tester model 32-76e – – AB5700
The 32-76e Coefficient of friction / peel tester offers precise and repeatable results with digital force signaling and data acquisition software.
SKU: AB5700 - Corrosion / Weathering, Hull Roughness Gauge, Surface Characteristics
Hull Roughness Gauge – DC9000
The TQC Hull Roughness Gauge has made the next evolutionary step in hull roughness surveys. Surpassing the industrial standards with an easy to operate 4-way directional push button, graphical representations, storage of data in multiple batches and survey reports in Microsoft Excel®. The whole system fits into a small sized waterproof rugged casing that is allowed as carry on travel luggage and benefits your overseas travel plans.
Controlling the roughness of a ship’s hull plays an important role in the operating costs of a vessel. The roughness of a ship’s hull increases mainly due to corrosion, pitting, plate undulation, mechanical damage, dry spray and above all biofouling. Proper maintenance and the correct application of high-end anti-fouling coatings reduce the hydrodynamic effects and will lead to significant savings on fuel consumption and CO2 emissions.
The hull roughness is measured during in-docking and out-docking. The Hull Roughness Gauge measures the AHR value (Average Hull Roughness) of sea-going vessels. AHR is the ‘mean’ of all the vessel’s hull roughness readings and is the measure against which ship’s performance is correlated.
The TQC Hull roughness Gauge consists of a Control unit and a Sensor unit.
The Hull Roughness Control unit can be operated with just one hand, a 4-way directional push button operates an intuitive menu on a large illuminated display. The neck strap keeps the users’ hands-free when required.The Sensor unit is equipped with three non-slip wheels and a carbide tipped stylus and is moved over the ship’s hull in a horizontal way collecting series of measurements. A set of LED’s indicate the status of the instrument so operation is possible without observing the control unit.
Statistics, time/date and location of each series and the average hull roughness are automatically calculated and stored in the Control unit. Using the supplied USB-cable and software you instantly create inspection reports in Microsoft Excel. Your own company logo and or -details can be incorporated to restyle your reports.
Accuracy: +/- 5 microns or or Memory: Enough for 4 complete surveys done both in- and out-docking, totally over 10.000 readings
Location storage: Simply point and click the hull location in the displayed graphical representation of the ship’s hull.
Units: Microns
Speed: 50 mm/s, with speed indication LED in the Sensor unit
Interface: USB serial to PC connection
Power supply: 4 AA type Alkaline Cells, available worldwide
Calibration certificate: includedSKU: DC9000 - Conveyor Ground Tester
Conveyor Ground Test – LD5900
Conveyor ground test with five steps which informs you whether items to be coated are sufficiently grounded. Designed for electrostatic coating applications.
A poor ground of the pieces to be coated may result in a poor quality of the electrostatic coating work. Coating thickness may not be sufficient or the pieces may not be even covered.
Consult your paint manufacturer or the supplier of your spray equipment for correct values.
The LD5900 is a low cost, easy to use ground check that is battery operated.
SKU: LD5900 - ASTM D3276-07, Climate Testing, Dewpoint, ISO 8502-4, Recorders / Dataloggers, Temperature, Temperature and Climatic Testing
DewCheck 4 Series 2 – Dewpoint Meter | Dewmeter DC7100
ASTM D3276-07, Climate Testing, Dewpoint, ISO 8502-4, Recorders / Dataloggers, Temperature, Temperature and Climatic TestingDewCheck 4 Series 2 – Dewpoint Meter | Dewmeter DC7100
The TQC DewCheck 4 – Dewpoint Meter (DPM)/ Dewmeter is an extremely versatile dewpoint meter to measure and record all climate parameters required to treat surfaces. This easy to use and robust dewmeter conforms to ISO 8502-4 & ASTM D3276-07 and measures the relative humidity (%RH), ambient temperature (Ta) and surface temperature (Ts) and calculates the dewpoint temperature (Td) and the difference between the dewpoint temperature and the surface temperature (ÄT). The difference between the surface temperature and dewpoint temperature indicates the optimal climate conditions for painting. All parameters can be stored in the dew meter’s memory, tagged with a date and time.
For communication between DewCheck 4 dewmeter and a PC the DewCheck dew meter USB cable is standard supplied. To analyze the data the DewCheck 4 comes with the special Ideal Finish Analysis software. This software is the most advanced temperature and humidity monitoring software package for Dew-point Meters available today. It offers user friendly reporting functions for standard production work as well as advanced calculations for in depth analysis of the climate parameters prior to coating. Detailed graphic representations and custom reports help to make the right decisions.
SKU: DC7100 - ASTM D1084, ASTM D5725, Contact Angle Testing, Tappi T588
DAT 1121 Dynamic Contact Angle Tester – PG1050 or DAT 1122 – PG1051
ASTM D1084, ASTM D5725, Contact Angle Testing, Tappi T588DAT 1121 Dynamic Contact Angle Tester – PG1050 or DAT 1122 – PG1051
DAT 1121 Dynamic Contact Angle Tester – PG1050 – or – DAT 1122 Dynamic Contact Angle Tester – PG1051
The DAT measures the contact angle (dynamic and static), surface tension, penetration, surface energy and spreading. The instrument uses a sophisticated camera to capture the fall/ shape of the drop, the shape on the sample and eventually the penetration. The pump and the camera work closely together. This is critical to have the correct amount of liquid and have each test start at the same time.
SKU: n/a - ASTM D5946, ASTM D724, Contact Angle Testing, TAPPI T458
PGX+ Pocket Goniometer – PG1000
Pocket Goniometer PGX+ defines several surface properties for quality control. The instrument measures the dynamic and static contact angle of a standard liquid. During testing the instrument is connected to the special PC software.
SKU: PG1000
