Main Menu
Surface Characteristics Accessories
Showing all 23 results
- PosiTector 6000 Accessories, Surface Characteristics Accessories, Surface Profile, Surface Profile Gage Accessories
Testex™ Press-O-Film™ Replica Tape
PosiTector 6000 Accessories, Surface Characteristics Accessories, Surface Profile, Surface Profile Gage AccessoriesTestex™ Press-O-Film™ Replica Tape
Optical Grade XC Testex Replica Tape available — provides higher quality SDF surface data files than conventional replica tape (for use with PosiTector RTR 3D models).
Each roll of Testex Tape includes 50 pieces (Impressions).
SKU: n/a - Salt/Chloride Testing, Surface Characteristics Accessories, Surface Cleanliness/Preperations
TQC Sheen Bresle Patches + Needle – LD6515
Salt/Chloride Testing, Surface Characteristics Accessories, Surface Cleanliness/PreperationsTQC Sheen Bresle Patches + Needle – LD6515
The new TQC Sheen Bresle Patches + Needle is stronger, whilst at the same time has a clean removal, negligible patch contamination, no breaking foam and is silicone-free.
TQC Sheen Bresle Patches, 25 pieces + needle
SKU: LD6515 - Surface Characteristics Accessories, Surface Cleanliness/Preperations
Replacement Tape For Dust Test Kit – SP3209
Surface Characteristics Accessories, Surface Cleanliness/PreperationsReplacement Tape For Dust Test Kit – SP3209
The TQC Dust Test Kit according to ISO 8502-3 allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish. The dust test kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust.
SKU: SP3209 - ASTM D4417, Surface Characteristics Accessories, Surface Profile
Testex Replica Tape | Press-O-Film
Replica tape for measuring blasted surface profiles. By placing the Tqc replica tape on the surface and rubbing over it, the Rt (total roughness) or peak-to-valley height of the profile can be taken and then measured with a film thickness meter.
1. TQC Replica tape consists of a layer of compressible foam affixed to an incompressible polyester substrate.
2.When pressed against a roughened/gritblasted (steel) surface, the foam collapses acquiring an impression of the surface.
3.Placing the compressed tape between the anvils of the SP1570 micrometric thickness gage, and subtracting the contribution of the incompressible substrate (50 micrometers or 0.002 inches), gives a measure of the surface profile.One box of Testex contains tape for 50 measurements.
SKU: n/a - ASTM B117, ISO 9227, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics Accessories
C&W Specialist Salt 4 buckets of 5 kg – CW4096
ASTM B117, ISO 9227, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics AccessoriesC&W Specialist Salt 4 buckets of 5 kg – CW4096
C&W Specialist Salt is Sodium Chloride which quality complies to the stringent ASTM B117 standard. The Sodium Chloride’s grain and purity is specially formulated for saline spray (fog) for corrosion testing with C&W Salt Spray and CCT cabinets.
SKU: VF7610 - PosiTector 6000 Accessories, Surface Characteristics Accessories, Surface Profile
Cleaning Cards for PosiTector® RTR (20-Pack)
PosiTector 6000 Accessories, Surface Characteristics Accessories, Surface ProfileCleaning Cards for PosiTector® RTR (20-Pack)
Pre-moistened with isopropyl alcohol to clean residual adhesive and debris from the anvils helping to insure an accurate test.
Every PosiTector RTR ships with (5) cleaning cards. Additional cards are available (20 cards per pack).
SKU: RTRCLEANCARD