No products in the cart.
Shop
Showing 385–432 of 495 results
- PH / Conductivity, Salt/Chloride Testing, Surface Cleanliness/Preperations
CHLOR*TEST Kit (50 tests) Chlor-Test 50
PH / Conductivity, Salt/Chloride Testing, Surface Cleanliness/PreperationsCHLOR*TEST Kit (50 tests) Chlor-Test 50
CHLOR*TEST was developed for ease of use and to prevent outside and cross contamination. The components are premeasured to ensure accurate results in parts per million and micrograms per square centimeter. In addition, no temperature correction is needed for 5°C to 80°C (41°F to 176° F). Field test inspectors around the world will use this innovative product with confidence on virtually any surface at any angle.
SKU: Chlor-Test 50 - Salt/Chloride Testing, Surface Characteristics Accessories, Surface Cleanliness/Preperations
TQC Sheen Bresle Patches + Needle – LD6515
Salt/Chloride Testing, Surface Characteristics Accessories, Surface Cleanliness/PreperationsTQC Sheen Bresle Patches + Needle – LD6515
The new TQC Sheen Bresle Patches + Needle is stronger, whilst at the same time has a clean removal, negligible patch contamination, no breaking foam and is silicone-free.
TQC Sheen Bresle Patches, 25 pieces + needle
SKU: LD6515 - Viscosity Accessories
TEMPERATURE CONTROL JACKET FOR VISCOSITY CUP
The TQC Temperature Control Jacket for Viscosity Cup is a double jacketed casing of anodised aluminium with built-in spirit level to bring the viscosity beaker to the required temperature with cooled and heated liquids. Supplied with glass plate and tube connection.
SKU: n/a - Accessory Products, Viscosity Accessories
Tripod Stand for Viscosity Beaker (Stainless Steel) – VF2061
Accessory Products, Viscosity AccessoriesTripod Stand for Viscosity Beaker (Stainless Steel) – VF2061
The TQC Tripod Stand for Viscosity Cup is a stand that is easy to level with the adjustable feet of the unit and the built-in spirit level. The ring is made of stainless steel, the legs are made of stainless steel and the feet PVC. Suitable for all DIN, ISO and ASTM viscosity beakers.
SKU: VF2061 - Accessory Products, Paint Charts and Panels
Byko-Chart Penopac 1B – Penetration and Opacity Cards
The penopac card is used to measure coating appearance changes between the unsealed and sealed portion of the chart. Used to assess penetration resistance of architectural coatings. Consist lot to lot quality for optimum long term property studies
SKU: 2818 - Accessory Products, ASTM D244, ASTM D2805, ASTM D344, ISO 6504-3, Paint Charts and Panels, WFT Wet Film Thickness
Byko-Chart Opacity 2C
Accessory Products, ASTM D244, ASTM D2805, ASTM D344, ISO 6504-3, Paint Charts and Panels, WFT Wet Film ThicknessByko-Chart Opacity 2C
Clear Coated Paint Test Chart – 2A is a clear coated opacity chart with a size of: 140 x 254 mm (5.5 x 10 in). Bulk Discounts available for 4+ or more boxes.
SKU: 2813 - Accessory Products, ASTM D2244, ASTM D2805, ASTM D344, ISO 6504-3, Paint Charts and Panels
Byko-Chart Opacity 2A
Accessory Products, ASTM D2244, ASTM D2805, ASTM D344, ISO 6504-3, Paint Charts and PanelsByko-Chart Opacity 2A
The opacity chart consists of black and white areas with sufficient room to use color measurement instruments. Optimum chart to measure coating opacity. Large product offering to fit all applications.
SKU: 2810 - Accessory Products, Surface Characteristics Accessories, Surface Cleanliness/Preperations
Replacement Tape For Dust Test Kit – SP3209
Accessory Products, Surface Characteristics Accessories, Surface Cleanliness/PreperationsReplacement Tape For Dust Test Kit – SP3209
The TQC Dust Test Kit according to ISO 8502-3 allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish. The dust test kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust.
SKU: SP3209 - ASTM D4417, Surface Characteristics Accessories, Surface Profile
Testex Replica Tape | Press-O-Film
Replica tape for measuring blasted surface profiles. By placing the Tqc replica tape on the surface and rubbing over it, the Rt (total roughness) or peak-to-valley height of the profile can be taken and then measured with a film thickness meter.
1. TQC Replica tape consists of a layer of compressible foam affixed to an incompressible polyester substrate.
2.When pressed against a roughened/gritblasted (steel) surface, the foam collapses acquiring an impression of the surface.
3.Placing the compressed tape between the anvils of the SP1570 micrometric thickness gage, and subtracting the contribution of the incompressible substrate (50 micrometers or 0.002 inches), gives a measure of the surface profile.One box of Testex contains tape for 50 measurements.
SKU: n/a - Accessory Products, ASTM B117, ISO 9227, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics Accessories
C&W Specialist Salt 4 buckets of 5 kg – CW4096
Accessory Products, ASTM B117, ISO 9227, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics AccessoriesC&W Specialist Salt 4 buckets of 5 kg – CW4096
C&W Specialist Salt is Sodium Chloride which quality complies to the stringent ASTM B117 standard. The Sodium Chloride’s grain and purity is specially formulated for saline spray (fog) for corrosion testing with C&W Salt Spray and CCT cabinets.
SKU: CW4096 - Pit Gages
Tri-Gauge – N88L-1
The Tri-Gauge is today’s most versatile Lever Pit Gauge, with its Metric and dual Imperial Scales. Additionally, the Tri-Gauge serves as a basic Weld Inspection Gauge for; Undercut Depth, Weld Crown Height, a Porosity (diameter) Comparator; and both Metric and Imperial Rules. The Tri-Gauge is fitted with a Patented pointer Offset Correction for improved accuracy and repeatability. Lever Pit Gauges are intended to evaluate corrosion, and not as an absolute measuring tool. The Tri-Gauge is supplied with a Pocket Protector type Case and Instructions.
SKU: N88L-1 - Headcovers and Powered Air Supplies
Tyvek Shoe Covers – 200 Pack – TY4505
Tyvek® 400 garments are composed of flash spun high-density polyethylene which creates a unique, nonwoven material available only from DuPont. Tyvek® 400 provides an ideal balance of protection, durability and comfort of any limited use fabric technology.
SKU: n/a - Pit Gages
Vessel Inspection Kit – N88-VI
Vessel Inspectors Kit
As Westerns Pit Gauge Product Series gains popularity, we are able to address various industry needs. When API Inspectors (510, 570, 653) see all of the different models of Pit Gauges we offer, they immediately want one of each! Unfortunately budget constrains take hold and hes limited to pick and choose his components. Simply due to customer requests, so we offer the Vessel Inspectors Kit.
The Reaching Plus Blade is 6 long, so it will deal with some of the worst Weight-Loss-Corrosion we often see in Vessels and Tanks. The cut-away nose, at the end of the Blade, allows the inspector to get right up to a Weld, and will often reach over welds.
Carrying Case, Reaching Pit Gauge (N88-5), Pocket Pit Gauge Blade (N88-4B), Basic Blade (N88-2B), Allan Key, Spare #1 Contact Point, and Operator Instructions.
Note: The Reaching Pit Gauge includes; Reaching Blade, Imperial Dial Indicator (w/ #2 Contact Point)Specified by a Senior Vessel Inspector, the Pocket Pit Gauge allows inspection on complex curvatures, such as the Knuckle Area on Vessel Heads, and even pump housings and impellers. As the name suggests, the Pocket Pit Gauge conveniently fits in your pocket (but so does the Basic Pit Gauge).vSKU: N88-VI
