No products in the cart.
Hardness / Scratch Resistance Accessories
Tip for hardness test Diameter 0.5 mm / R=0,25 – SP0012
Tip for hardness test Diameter 0.5 mm / R=0,25 – SP0012
$105.00
Tip for hardness test Diameter 0.5 mm / R=0,25 – SP0012
| Weight | .5 lbs |
|---|---|
| Dimensions | 12 × 12 × 6 in |
Related products
- Temperature, Temperature and Climatic Testing
Thermometer ST-610B with TC type K input – TE1000
A tough, high-quality thermometer suitable for use with the interchangeable type ‘K’ thermocouple probes.
The practical design, robust casing, large push buttons and the protective holster supplied with the instrument make the TE1000 suitable for use in heavy-duty conditions. The large display panel enables readability at a distance.
Equipped with functions for holding the current value as well as the maximum value.
Range : -50° to +1300°C
Resolution : 0,1°C or 0,1°F
Accuracy : ±(0,5%±1°C), ±(0,5%±2°F)
Dimensions : 165mm x 76mm x 43mmSKU: TE1000 - Adhesion, ASTM D4541, Pull Off
Dolly Drill For Adhesion Test – LD9250
The TQC Dolly Drill is the perfect tool to remove the excess of glue and cut through the coating around dollies in order to prepare the dolly for the adhesion test. Fixed positioning is assured with the three strong magnets, allowing the drill to remove the coating around the dolly without putting any force on the dolly. Manually removing the access of glue and cutting through the coating is a hard job for inspectors that have to do many tests a day, which results in wrist and arm pains. The TQC Dolly Drill eases their work considerably, and increases the accuracy of the pull off adhesion tests because of a perfect vertical cutting movement down to the metal.
For the best reproducible results use the Adhesion tester AT, with the hydraulics and auto positioning feature of the pull-off head.
SKU: LD9250 - Coating Thickness Gages
POSIPEN A – LD6000
PEN TYPE FERROUS THICKNESS GAGE .25-20 MILS
PosiPen has a very small, unique magnet which can be placed with pin-point accuracy on extremely small parts, and on peaks and valleys. Ideal for measuring non-magnetic coatings such as paint, enamel, plating, hot-dip galvanizing on steel.
Used for:
Small, hot or hard-to-reach surfaces
Spot Checks – conveniently fits in a shirt pocket
Hot Sprayed CoatingsIdeal for:
Refineries, petrochemical plants
Platers – electroplating, chrome, zinc, galvanizing
Powder coatersSKU: LD6000 - Film Application
BIRD-TYPE FILM APPLICATORS, 4-SIDED
TQC Bird-type film applicator with flat edges. Four application sides for applying 4 different pre-defined thicknesses. The TQC Bird-type applicator is available in film width 50, 75 and 100mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
We can give no guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.Surface treatment:
polishedOverall accuracy:
± 2 µm*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.SKU: n/a
