Showing all 44 results
The PosiTector HHD High Voltage Holiday Detector detects holidays, porosity, pinholes, leaks, and other discontinuities in coatings, linings, and membranes using pulse DC
-Lightweight, ergonomic design provides comfortable all-day use, reducing operator fatigue
-Regulated pulse DC voltage output that won’t change under load— ±5% voltage accuracy
-Voltage calculator feature—choose one of 11 international standards, and input the coating thickness to automatically calculate the required test voltage
-Extensive electrode options—choose from a wide range of rolling spring and flat wire brush electrodes or use electrodes from other manufacturers with optional adaptors—custom sizes available upon request
Long Form Certificate of Calibration included with each instrument
Conforms to ASTM D4787/D5162/D6747/D7953/G62, ISO 29601, NACE SP0188/SP0274/SP0490, AS3894.1
The PosiTector 6000 Coating Thickness Gauge is available in 2 models: the PosiTector 6000 Standard and Advanced. There are many probes to choose from either with a PosiTector 6000 gauge body or you may purchase a probe separately. See the PosiTector 6000 descriptions and downloadable pdf brochures in the description area below for more info.
POSITEST F/FM/G/GM COATING THICKNESS GAGE
Magnetic Coating Thickness Gages for Non-Magnetic Coatings on Steel – PosiTest magnetic pull-off thickness gage (banana gauge) for the non-destructive measurement of non-magnetic coatings (paint, enamel, galvanizing, metalizing, plating, etc.) on steel.
Highly wear resistant Carbide Probe for longest life and continuous accuracy
Extra rugged housing, not affected by mechanical shock, water, acid or solvents
Unique overall design, fully supported, positive positioning, no pivoting tendencies during measurement
Positive visual and audible indicators to designate when thickness reading is established
“V” grooves in probe housing and gage base allow correct positioning on cylindrical objects
Certificate of Calibration showing traceability to PTB included (Long Form)
Conforms to ASTM D7091/B499, ISO 2808 and others
PosiPen® has a very small, unique magnet which can be placed with pin-point accuracy on extremely small parts, and on peaks and valleys. Ideal for measuring non-magnetic coatings such as paint, enamel, plating, and hot-dip galvanizing on steel. Can be used on small, hot or hard-to-reach surfaces.
Ideal for checking the accuracy and operation of adhesion testers and is an important component in fulfilling both ISO and in-house quality control requirements.
The PosiTest® AT Verifier and included documents allow the user to certify the accuracy of PosiTest® Adhesion Testers.
Heavy-duty, waterproof Pelican case complete with a custom foam insert to securely hold your PosiTest AT-A instrument. Pelican cases can be purchased as an upgrade from the standard case at the time of purchase, or as an accessory.
Waterproof
Two easy open Press & Pull latches
Comfortable double-layered, soft-grip handle
Strong, lightweight
Two padlockable hasps
Meets airline regulations for carry-on luggage*
*Check with your airline for exact measurement requirements
EXTERIOR (L X W X D)
18.20″ x 13.40″ x 6.70″ (46.2 x 34 x 17 cm)
The innovative PosiPatch™ (sold separately) attaches to steel surfaces using a unique magnetic ring. Like the Standard Magnetic Ring, the Flexible Magnetic ring leaves no messy adhesive residue to clean. Intended for pipes and other tight diameters, it allows the PosiPatch™ to form a tight, leak-free seal on inside and outside diameters greater than 10 cm (4 in.).*
The Standard Magnetic Ring continues to be included in all PosiPatch™ Kits and is the first choice for flat surfaces and curved surfaces with diameters greater than 100 cm (40 in.).
*Flexible Patch Minimum ID diameter is 12 cm (4.5 in.)
The PosiTest AT Pull-off Adhesion Tester uses hydraulic pressure to apply perpendicular force and debond an aluminum pull stub from the coating surface. Measure the adhesive and cohesive strength of coatings and coating systems in the laboratory, shop or field using this self-aligning hydraulic tensile adhesion testing kit.
ResinLab EP11HT 2-Part Epoxy with additional glue, mixing sticks, palettes and cotton swabs
Approximate Epoxy Yield*
*Actual results will vary based on amount of epoxy used per dolly and waste
Simulate a coating over a particular substrate material or shape. Gage performance can be conveniently verified on a regular basis as required by some international test methods.
For use with all Type 2, electronic coating thickness gages.
Protects the probe from damage or premature wear when placed over hot or abrasive surfaces
Can be placed on top of soft or tacky coating films to obtain thickness measurements without the gage probe depressing the coating film.
Certified coated metal plates and polystyrene blocks are ideal for verifying the accuracy and operation of coating thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements.
Many organizations require verification of gage accuracy at the test site each time a coating thickness gage is put into service and at frequent intervals during use. Ideal for this purpose, DeFelsko certified coating thickness standards have measured values traceable to a National Metrology Institution.
Pre-moistened with isopropyl alcohol to clean residual adhesive and debris from the anvils helping to insure an accurate test.
Every PosiTector RTR ships with (5) cleaning cards. Additional cards are available (20 cards per pack).
Used to verify the accuracy and operation of PosiTector® RTR and other spring micrometer replica tape readers. Ideal for fulfilling both ISO and in-house quality control requirements. Includes Certificate of Calibration traceable to PTB. For use with the PosiTector® RTR H, PosiTector® RTR 3D
Accuracy: ±1.25 microns
Great Lakes Gages, LLC
3689 Hadley Rd.
Metamora, MI 48455
