No products in the cart.
Adhesion Categories
Adhesion
Showing all 17 results
- Adhesion, ASTM D3359, ASTM D4417, ASTM D4417-B, BS 7079-B4, IMO MSC.215(82), ISO 2409, ISO 2808-3, ISO 8501-1, ISO 8502-3, ISO 8502-4, ISO 8502-6, ISO 8502-9, ISO 8503-01, ISO 8503-02, Optical Inspection Tools, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics, Surface Cleanliness/Preperations, Surface Profile, US Navy NSI 009-32, US Navy PPI 63101-000
Pretreatment Test Kit (PTK) Basic or Full Kit – SP7315 or SP7316
Adhesion, ASTM D3359, ASTM D4417, ASTM D4417-B, BS 7079-B4, IMO MSC.215(82), ISO 2409, ISO 2808-3, ISO 8501-1, ISO 8502-3, ISO 8502-4, ISO 8502-6, ISO 8502-9, ISO 8503-01, ISO 8503-02, Optical Inspection Tools, PH / Conductivity, Salt/Chloride Testing, Surface Characteristics, Surface Cleanliness/Preperations, Surface Profile, US Navy NSI 009-32, US Navy PPI 63101-000Pretreatment Test Kit (PTK) Basic or Full Kit – SP7315 or SP7316
The Pretreatment Test Kit is especially composed to control all relevant parameters during the pretreatment of steel prior to painting. The PTK is available as BASIC KIT and FULL KIT.
See Datasheet for Basic and Full kit comparisons
SKU: n/a - Adhesion
Cross Cut Adhesion Test Kit CC1000 (exclud. knife) VF1856
CC1000 BASIC (holder only) VF1848 includes the TQC Cross cut tester CC1000 Basic (Holder only, knives and accessories not included).
CC1000 KIT VF1856 includes a soft grip handle (Excl. knife, this needs to be ordered separately), nylon brush, illuminated magnifier, adhesive tape (adhesion to steel 4.3N/cm), a 4 mm Allen key, and a sturdy case
SKU: VF1856 - Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140
CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.
FULLY ADJUSTABLE
The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.
SKU: SP1695 - Adhesion, Adhesion (Wood), DFT Dry Film Thickness Gauges, ISO 2409, Paint Thickness Gauge, WFT Wet Film Thickness, ГОСТ 15140
Cross Cut Adhesion Test Kit (Master Paint Plate) – SP3000
Adhesion, Adhesion (Wood), DFT Dry Film Thickness Gauges, ISO 2409, Paint Thickness Gauge, WFT Wet Film Thickness, ГОСТ 15140Cross Cut Adhesion Test Kit (Master Paint Plate) – SP3000
The TQC Cross Cut Adhesion Test KIT (Master Paint Plate) is a stainless steel measuring tool that features: a 1 mm, 1.5 mm, 2 mm and 3 mm cross cut adhesion test according NEN-EN-ISO 2409:2003 and ASTM D 3359 (X-cut) Andreas cross.
Additional tools
- Wet film thickness gauge ranging from 50 microns up to 160 microns.
- On the corners there is an edge grind checker for correct roundness of edges.
- At the bottom is a wet film applicator ranging from 0 to 180 µm.
- The top edge provides a leveling test, an indication of the viscosity of the coating.
Delivery includes cutting tool and tape.
Tapes for the cross cut adhesion test
Tape For Adhesion Test according ISO 2409:2003
Tape For Adhesion Test according ISO 2409:1999 can be ordered separately as well.SKU: SP3000 - Adhesion, Adhesion (Wood)
Adhesion Test Kit (HPK) – SP3100
Adhesion Test Kit for Coatings on Wood
The TQC Adhesion Test Kit (HPK) is a method developed in the Netherlands by FOSAG and SKH. This method determines the adhesion of new and old paint layers on wood and wood like materials. The damage on the substrate will be reduced to a minimum. The adhesion is judged by comparing the removed paint on the tape and the remaining paint on the wood. Finally illustrations are used for classifying the damage from class 0 to 5. Delivery includes cutting tool and also tape.
The Tape For Adhesion Test can be ordered separately as well.
SKU: SP3100 - Adhesion, BS EN ISO8502-2, Surface Cleanliness/Preperations
TQC Dust Test Kit – SP3200
The TQC Dust Test Kit according to ISO 8502-3 allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish. The dust test kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust.
SKU: SP3200 - Accessory Products, Adhesion, ASTM D4541, Pull Off
Dolly Drill For Adhesion Test – LD9250
The TQC Dolly Drill is the perfect tool to remove the excess of glue and cut through the coating around dollies in order to prepare the dolly for the adhesion test. Fixed positioning is assured with the three strong magnets, allowing the drill to remove the coating around the dolly without putting any force on the dolly. Manually removing the access of glue and cutting through the coating is a hard job for inspectors that have to do many tests a day, which results in wrist and arm pains. The TQC Dolly Drill eases their work considerably, and increases the accuracy of the pull off adhesion tests because of a perfect vertical cutting movement down to the metal.
For the best reproducible results use the Adhesion tester AT, with the hydraulics and auto positioning feature of the pull-off head.
SKU: LD9250 - Adhesion
PosiTest AT Pull-off Adhesion Tester – Manual or Automatic
The PosiTest AT Pull-off Adhesion Tester uses hydraulic pressure to apply perpendicular force and debond an aluminum pull stub from the coating surface. Measure the adhesive and cohesive strength of coatings and coating systems in the laboratory, shop or field using this self-aligning hydraulic tensile adhesion testing kit.
SKU: n/a - Adhesion, Elasticity Testing, Hardness Tester, Resistance & Deformation
TQC SHEEN Manual Cupping Test – SP4400
Adhesion, Elasticity Testing, Hardness Tester, Resistance & DeformationTQC SHEEN Manual Cupping Test – SP4400
The TQC Sheen Manual Cupping Test is a revolutionary apparatus for testing the resistivity of coatings at various stages of deformation in accordance
with ISO 1520. The built in gear-box minimizes the manual force which is required to deform the test panel,
allowing to perform a smooth deformation. The degree or deformation is digitally displayed at a resolution of
0.01 mm. Mandatory test in Qualicoat, QIB and GSB accredited laboratories.SKU: SP4400 - Adhesion, Scratch Testing
TQC Cross cut tester CC1000 Basic (Holder only, knife not included) – VF1848
Adhesion, Scratch TestingTQC Cross cut tester CC1000 Basic (Holder only, knife not included) – VF1848
TQC Cross cut tester CC1000 Basic Test Kit (Holder only, knife and accessories not included) – VF1848
Buy knives by adding them below or click here
View the CC1000 Kit with Holder and Accessories (exclud. knife) here.
SKU: VF1848
