No products in the cart.
DFT Dry Film Thickness Gauges, Dry Film Thickness
POSIPEN A – LD6000
PEN TYPE FERROUS THICKNESS GAGE .25-20 MILS
PosiPen has a very small, unique magnet which can be placed with pin-point accuracy on extremely small parts, and on peaks and valleys. Ideal for measuring non-magnetic coatings such as paint, enamel, plating, hot-dip galvanizing on steel.
Used for:
Small, hot or hard-to-reach surfaces
Spot Checks – conveniently fits in a shirt pocket
Hot Sprayed Coatings
Ideal for:
Refineries, petrochemical plants
Platers – electroplating, chrome, zinc, galvanizing
Powder coaters
$265.00
ORDERING INFORMATION
LD6000
Posipen A Coating Thickness Meter, calibration certificate included
| Weight | 2 lbs |
|---|---|
| Dimensions | 12 × 9 × 4 in |
Related products
- Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140
CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.
FULLY ADJUSTABLE
The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.
SKU: SP1695 - Accessory Products, Adhesion, ASTM D4541, Pull Off
Dolly Drill For Adhesion Test – LD9250
The TQC Dolly Drill is the perfect tool to remove the excess of glue and cut through the coating around dollies in order to prepare the dolly for the adhesion test. Fixed positioning is assured with the three strong magnets, allowing the drill to remove the coating around the dolly without putting any force on the dolly. Manually removing the access of glue and cutting through the coating is a hard job for inspectors that have to do many tests a day, which results in wrist and arm pains. The TQC Dolly Drill eases their work considerably, and increases the accuracy of the pull off adhesion tests because of a perfect vertical cutting movement down to the metal.
For the best reproducible results use the Adhesion tester AT, with the hydraulics and auto positioning feature of the pull-off head.
SKU: LD9250 - Film Application
BIRD-TYPE FILM APPLICATORS, 4-SIDED
TQC Bird-type film applicator with flat edges. Four application sides for applying 4 different pre-defined thicknesses. The TQC Bird-type applicator is available in film width 50, 75 and 100mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
We can give no guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.Surface treatment:
polishedOverall accuracy:
± 2 µm*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.SKU: n/a - Destructive Dry Film Thickness Gage, DFT Dry Film Thickness Gauges, DIN 50986, Dry Film Thickness, ISO 2808, Thickness Testing
TQC SP1000 Super-pig Destructive Dry Film Thickness Gauge – SP1100
Destructive Dry Film Thickness Gage, DFT Dry Film Thickness Gauges, DIN 50986, Dry Film Thickness, ISO 2808, Thickness TestingTQC SP1000 Super-pig Destructive Dry Film Thickness Gauge – SP1100
The TQC SP1100 Superpig is a destructive precision tool for inspection and thickness measurement on single or multiple coats on virtually all substrates, including wood, plastics, metals etc. Also observes and measures substrate and film defects. Applies a small incision in the layer of paint, and uses an integrated microscope with measuring reticle.
Features:
– Made of Titanium anodised aluminum
– Three knife sizes and one crosscut knife in one holder
– Ergonomic design: revolving-system to change knifes
– Bright white LED lights ensure clear vision through the microscope
– Small size eases use in corners
– Engraved scaling (D-factor) for easy calculationsSP1100
Super-pig, destructive coating thickness gauge, range: 2 to 2000 microns
Microscope : Magnification 50X (with graduation-scale)
Scale range : 0,00 — 2,50 mm (rectilinear measured)
Variation : Accuracy depends on chisel cut angle and users reading Battery : AAA 1,5 volt
Material : Titanium anodised aluminum
Width : 25mm
Height : 110mm
Length : 60mm
Delivery: SuperPIG with wrist strap, black marker, cutting knifes 1, 2, 3, hex diagonal wrench, leather pouch with beltclipSKU: SP1100
