No products in the cart.
Laboratory Equipment
Hotplate Stirrer With Temperature Probe – VF8800
TQC Hotplate Stirrer with external temperature probe, support rod and clamp.
$900.00
Documents
Description
TQC Hotplate Stirrer with external temperature probe, support rod and clamp.
The ceramic coated hotplate of the TQC Hotplate Stirrer has a high chemical/acid resistance. The Jog-Shuttle switch (Turn + Push) eases setting heat (up to 380°C), stirring speed (80-1500 RPM) and time. The illuminated display shows these values, and they can be stored in the memory. The temperature is adjustable in 0.5°C steps., stirring speed in 5 RPM steps. TQC Hotplate Stirrer has a capacity of 20 liter.
The end of a run or probe failure is indicated with an acoustic signal. The TQC Hotplate Stirrer is protected against overheating and overload.
ORDERING INFORMATION
VF8800
TQC Digital Hotplate Stirrer, incl. temperature probe
| Weight | 2 lbs |
|---|---|
| Dimensions | 12 × 9 × 4 in |
Related products
- Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140
CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.
FULLY ADJUSTABLE
The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.
SKU: SP1695 - Conveyor Ground Tester
Conveyor Ground Test – LD5900
Conveyor ground test with five steps which informs you whether items to be coated are sufficiently grounded. Designed for electrostatic coating applications.
A poor ground of the pieces to be coated may result in a poor quality of the electrostatic coating work. Coating thickness may not be sufficient or the pieces may not be even covered.
Consult your paint manufacturer or the supplier of your spray equipment for correct values.
The LD5900 is a low cost, easy to use ground check that is battery operated.
SKU: LD5900 - Accessory Products, Adhesion, ASTM D4541, Pull Off
Dolly Drill For Adhesion Test – LD9250
The TQC Dolly Drill is the perfect tool to remove the excess of glue and cut through the coating around dollies in order to prepare the dolly for the adhesion test. Fixed positioning is assured with the three strong magnets, allowing the drill to remove the coating around the dolly without putting any force on the dolly. Manually removing the access of glue and cutting through the coating is a hard job for inspectors that have to do many tests a day, which results in wrist and arm pains. The TQC Dolly Drill eases their work considerably, and increases the accuracy of the pull off adhesion tests because of a perfect vertical cutting movement down to the metal.
For the best reproducible results use the Adhesion tester AT, with the hydraulics and auto positioning feature of the pull-off head.
SKU: LD9250 - Film Application
BIRD-TYPE FILM APPLICATORS, 4-SIDED
TQC Bird-type film applicator with flat edges. Four application sides for applying 4 different pre-defined thicknesses. The TQC Bird-type applicator is available in film width 50, 75 and 100mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
We can give no guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.Surface treatment:
polishedOverall accuracy:
± 2 µm*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.SKU: n/a - ASTM D3276-07, Climate Testing, Dewpoint, ISO 8502-4, Recorders / Dataloggers, Temperature, Temperature and Climatic Testing
DewCheck 4 Series 2 – Dewpoint Meter | Dewmeter DC7100
ASTM D3276-07, Climate Testing, Dewpoint, ISO 8502-4, Recorders / Dataloggers, Temperature, Temperature and Climatic TestingDewCheck 4 Series 2 – Dewpoint Meter | Dewmeter DC7100
The TQC DewCheck 4 – Dewpoint Meter (DPM)/ Dewmeter is an extremely versatile dewpoint meter to measure and record all climate parameters required to treat surfaces. This easy to use and robust dewmeter conforms to ISO 8502-4 & ASTM D3276-07 and measures the relative humidity (%RH), ambient temperature (Ta) and surface temperature (Ts) and calculates the dewpoint temperature (Td) and the difference between the dewpoint temperature and the surface temperature (ÄT). The difference between the surface temperature and dewpoint temperature indicates the optimal climate conditions for painting. All parameters can be stored in the dew meter’s memory, tagged with a date and time.
For communication between DewCheck 4 dewmeter and a PC the DewCheck dew meter USB cable is standard supplied. To analyze the data the DewCheck 4 comes with the special Ideal Finish Analysis software. This software is the most advanced temperature and humidity monitoring software package for Dew-point Meters available today. It offers user friendly reporting functions for standard production work as well as advanced calculations for in depth analysis of the climate parameters prior to coating. Detailed graphic representations and custom reports help to make the right decisions.
SKU: DC7100
