No products in the cart.
Accessory Products, Hardness / Scratch Resistance Accessories
Standard Test Disc (87-89) for Barcol GYZJ-934-1 – VF6506
Standard Test Disc (87-89) for Barcol GYZJ-934-1
$21.00
Standard Test Disc (87-89) for Barcol GYZJ-934-1
| Weight | .1 lbs |
|---|---|
| Dimensions | 1 × 1 × 1 in |
Related products
- Film Application
BIRD-TYPE FILM APPLICATORS, SINGLE GAP
TQC Bird-type film applicator with one flat edge. One application side for applying 1 pre-defined thickness. The TQC Bird-type applicator single gap is available in film width 50 and 75 mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
Some models are equipped with removable guidance plates for straight application.
We can not give guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type film applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.Surface treatment:
polishedOverall accuracy:
± 2 µm*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.SKU: n/a - Destructive Dry Film Thickness Gage, DFT Dry Film Thickness Gauges, DIN 50986, Dry Film Thickness, ISO 2808, Thickness Testing
TQC SP1000 Super-pig Destructive Dry Film Thickness Gauge – SP1100
Destructive Dry Film Thickness Gage, DFT Dry Film Thickness Gauges, DIN 50986, Dry Film Thickness, ISO 2808, Thickness TestingTQC SP1000 Super-pig Destructive Dry Film Thickness Gauge – SP1100
The TQC SP1100 Superpig is a destructive precision tool for inspection and thickness measurement on single or multiple coats on virtually all substrates, including wood, plastics, metals etc. Also observes and measures substrate and film defects. Applies a small incision in the layer of paint, and uses an integrated microscope with measuring reticle.
Features:
– Made of Titanium anodised aluminum
– Three knife sizes and one crosscut knife in one holder
– Ergonomic design: revolving-system to change knifes
– Bright white LED lights ensure clear vision through the microscope
– Small size eases use in corners
– Engraved scaling (D-factor) for easy calculationsSP1100
Super-pig, destructive coating thickness gauge, range: 2 to 2000 microns
Microscope : Magnification 50X (with graduation-scale)
Scale range : 0,00 — 2,50 mm (rectilinear measured)
Variation : Accuracy depends on chisel cut angle and users reading Battery : AAA 1,5 volt
Material : Titanium anodised aluminum
Width : 25mm
Height : 110mm
Length : 60mm
Delivery: SuperPIG with wrist strap, black marker, cutting knifes 1, 2, 3, hex diagonal wrench, leather pouch with beltclipSKU: SP1100 - Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140
CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.
FULLY ADJUSTABLE
The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.
SKU: SP1695 - Accessory Products, Climate Testing Accessories, CurveX Tools and Supplies
WIRE-TYPE PROBES FOR CURVEX DATALOGGER CX2063,64,67
Accessory Products, Climate Testing Accessories, CurveX Tools and SuppliesWIRE-TYPE PROBES FOR CURVEX DATALOGGER CX2063,64,67
Wire-type probes to measure either air or surface temperature. Measuring element is an open thermocouple that can be attached by adhesive tape or other mechanical means.
SKU: n/a
