The TQC Karsten Tube Penetration Test is a simple test for measuring the degree or water penetration into building materials such as concrete, stone and plaster. The test consists or a glass tube filled with water, bonded to the test material with plastiline. Water pressure is then exerted on the surface. A graduated scale indicates, over time, the amount or water penetrated into the surface.
$425.00
li7500_TQC-Karsten-Tube-Penetration-Test_d44-14.pdf (93.43 KB)
karsten-tube-penetration-test-li7500-m44-14.pdf (1.46 MB)
li7500_b44-14.pdf (150.72 KB)
The TQC Karsten Tube Penetration Test is a simple test for measuring the degree or water penetration into building materials such as concrete, stone and plaster. The test consists or a glass tube filled with water, bonded to the test material with plastiline. Water pressure is then exerted on the surface. A graduated scale indicates, over time, the amount or water penetrated into the surface.
The TQC Karsten Tube Penetration Test contains 3 tubes for horizontal surfaces, 3 tubes for vertical surfaces (or at choice any other combination of total 6 tubes), a water bottle, marker and putty to place the tubes leak-tight on the surface. Additional vertical or horizontal tubes are available on request.
| Weight | 5 lbs |
|---|---|
| Dimensions | 18 × 12 × 8 in |
PEN TYPE FERROUS THICKNESS GAGE .25-20 MILS
PosiPen has a very small, unique magnet which can be placed with pin-point accuracy on extremely small parts, and on peaks and valleys. Ideal for measuring non-magnetic coatings such as paint, enamel, plating, hot-dip galvanizing on steel.
Used for:
Small, hot or hard-to-reach surfaces
Spot Checks – conveniently fits in a shirt pocket
Hot Sprayed Coatings
Ideal for:
Refineries, petrochemical plants
Platers – electroplating, chrome, zinc, galvanizing
Powder coaters
The TQC SP1000 Superpig is a destructive precision tool for inspection and thickness measurement on single or multiple coats on virtually all substrates, including wood, plastics, metals etc. Also observes and measures substrate and film defects. Applies a small incision in the layer of paint, and uses an integrated microscope with measuring reticle.
Features:
– Made of Titanium anodised aluminum
– Three knife sizes and one crosscut knife in one holder
– Ergonomic design: revolving-system to change knifes
– Bright white LED lights ensure clear vision through the microscope
– Small size eases use in corners
– Engraved scaling (D-factor) for easy calculations
SP1000
Super-pig, destructive coating thickness gauge, range: 2 to 2000 microns
Microscope : Magnification 50X (with graduation-scale)
Scale range : 0,00 — 2,50 mm (rectilinear measured)
Variation : Accuracy depends on chisel cut angle and users reading Battery : AAA 1,5 volt
Material : Titanium anodised aluminum
Width : 25mm
Height : 110mm
Length : 60mm
Delivery: SuperPIG with wrist strap, black marker, cutting knifes 1, 2, 3, hex diagonal wrench, leather pouch with beltclip
TQC Bird-type film applicator with flat edges. Four application sides for applying 4 different pre-defined thicknesses. The TQC Bird-type applicator is available in film width 50, 75 and 100mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
We can give no guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.
Surface treatment:
polished
Overall accuracy:
± 2 µm
*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.
Great Lakes Gages, LLC
3689 Hadley Rd.
Metamora, MI 48455
