No products in the cart.
Accessory Products, CurveX Tools and Supplies
Datacable for CurveX 2 – CX2082
Serial Datacable for CurveX-2 Datalogger DB9 Female to 3,5mm stereo jack. Cable length +/- 1500 mm.
$105.00
Serial Datacable for CurveX-2 Datalogger DB9 Female to 3,5mm stereo jack. Cable length +/- 1500 mm.
| Weight | 1 lbs |
|---|---|
| Dimensions | 5 × 5 × 2 in |
Related products
- Conveyor Ground Tester
Conveyor Ground Test – LD5900
Conveyor ground test with five steps which informs you whether items to be coated are sufficiently grounded. Designed for electrostatic coating applications.
A poor ground of the pieces to be coated may result in a poor quality of the electrostatic coating work. Coating thickness may not be sufficient or the pieces may not be even covered.
Consult your paint manufacturer or the supplier of your spray equipment for correct values.
The LD5900 is a low cost, easy to use ground check that is battery operated.
SKU: LD5900 - Film Application
BIRD-TYPE FILM APPLICATORS, 4-SIDED
TQC Bird-type film applicator with flat edges. Four application sides for applying 4 different pre-defined thicknesses. The TQC Bird-type applicator is available in film width 50, 75 and 100mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
We can give no guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.Surface treatment:
polishedOverall accuracy:
± 2 µm*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.SKU: n/a - Film Application
BIRD-TYPE FILM APPLICATORS, SINGLE GAP
TQC Bird-type film applicator with one flat edge. One application side for applying 1 pre-defined thickness. The TQC Bird-type applicator single gap is available in film width 50 and 75 mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.
Some models are equipped with removable guidance plates for straight application.
We can not give guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type film applicator.
Material:
DAIDO 440C medical grade Martensitic stainless tool steel.
Sub Zero Vacuum hardened (+1756°C to -70°C), hardness HRC 55 (through hardened*) & tempered.Surface treatment:
polishedOverall accuracy:
± 2 µm*Through hardening versus Case-hardening or surface hardening.
Through-hardening means the metal uniformly is hardened throughout the piece. Case- or surface (face / frame) hardening only hardens the top layer of the metal. Once the top layer is degraded excessive wear and tear will occur on the product limiting its life time and affecting accuracy.SKU: n/a - Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140
CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
Adhesion, Adhesion (Wood), ASTM D3359, ISO 2409, ГОСТ 15140CC3000 Cross Cut Adhesion Test Kit (excluding knife) SP1695
The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.
FULLY ADJUSTABLE
The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.
SKU: SP1695 - Adhesion, Adhesion (Wood)
Adhesion Test Kit (HPK) – SP3100
Adhesion Test Kit for Coatings on Wood
The TQC Adhesion Test Kit (HPK) is a method developed in the Netherlands by FOSAG and SKH. This method determines the adhesion of new and old paint layers on wood and wood like materials. The damage on the substrate will be reduced to a minimum. The adhesion is judged by comparing the removed paint on the tape and the remaining paint on the wood. Finally illustrations are used for classifying the damage from class 0 to 5. Delivery includes cutting tool and also tape.
The Tape For Adhesion Test can be ordered separately as well.
SKU: SP3100
